Hyundai Elantra: Roof Trim / Roof Trim Assembly Repair procedures

Hyundai Elantra AD (2016-2020) Service Manual / Body (Interior and Exterior) / Roof Trim / Roof Trim Assembly Repair procedures

Replacement

•	Put on gloves to prevent hand injuries.

•	When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.

•	When removing the interior trim pieces, use a plastic panel removal tool not to damage the surface.

•	Take care not to bend or scratch the trim and panels.

1.	Remove the door weatherstrip.

2.	Remove the front seat. (Refer to Front Seat - "Front Seat Assembly")

3.	Remove the rear seat. (Refer to Rear Seat - "Rear Seat Assembly")

4.	Remove the front pillar trim. (Rear to Interior Trim - "Front Pillar Trim")

5.	Remove the canter pillar lower trim. (Rear to Interior Trim - "Center Pillar Trim")

6.	Remove the canter pillar upper trim. (Rear to Interior Trim - "Center Pillar Trim")

7.	Remove the rear pillar trim. (Rear to Interior Trim - "Rear Pillar Trim")

8.	Remove the sunvisor and retainer. (Rear to Roof Trim - "Sunvisor")

9.	Remove the assist handle. (Rear to Roof Trim - "Assist Handle")

10.	Remove the overhead console lamp. (Rear to Body Electrical System - "Overhead Console Lamp")

11.	Remove the room lamp. (Rear to Body Electrical System - "Room Lamp")

12.	Disconnect the ECM mirror connector. (Refer to Body Electrical System - "Electro Chromic Inside Rear View Mirror")

13.	Disconnect the rain sensor connector. (Refer to Body Electrical System - "Rain Sensor")

14.	Disconnect the roof trim main connector (A) and the mounting clips in the front pillar.

15.	Disconnect the sunroof motor connector (A).

16.

Remove the roof trim mounting clip and remove the roof trim assembly (A).

•	Be careful not to wrinkle on the roof trim.

17.	Remove the roof trim assembly (A) from the body panel and then carry it out of the vehicle through the rear door.

18.	Remove the vanity lamp. (Refer to Body Electrical - "Vanity Lamp')

19.

Remove roof trim wiring harness (A) from the roof trim (B).

•	Take care not to damage the roof trim wiring harness (A) when removing.

1.	When installing the roof trim wiring harness (A) on the roof trim (B), apply the hot melt continuously by using the hot melt gun tool.

2.	Put anti-noise pad on roof trim (B) to prevent the noise.

20.

To intall, reverse the removal procedure.

•	Make sure the connector is connected in properly.

•	Replace any damaged clips.

Roof Trim Assembly Components and Components Location

Component Location 1. Roof Trim Assembly ...

Interior Trim

...

Other information:

Hyundai Elantra AD (2016-2020) Service Manual: ESC OFF Switch Repair procedures
Removal 1. Turn ignition switch OFF and disconnect the negative (-) battery cable. 2. Remove the crash pad lower panel. (Refer to Body - "Crash Pad") 3. Remove the side crash pad switch. 4. Disconnect the ESC OFF switch connector. 5. Check the continuity between the switch termi ...

Hyundai Elantra AD (2016-2020) Service Manual: Specifications
Specifications Purge Control Solenoid Valve (PCSV) ? Specification ItemSpecificationCoil Resistance (?)22.0 ~ 26.0 [20°C(68°F)] Fuel Tank Pressure Sensor (FTPS) ? Type: Piezo-Resistive Pressure Sensor ? Specification Pressure [kPa (kgf/cm?, in H2O)]Output Voltage (V)-6.67 (-0.068 ...