Hyundai Elantra: Lubrication System / Oil Pan Repair procedures

Removal
1.
Remove the engine room under cover.
(Refer to Engine And Transaxle Assembly - "Engine Room Under Cover")
2.
Drain engine oil.
(Refer to Lubrication System - "Engine Oil")
3.
Remove the oil pan (A).
(1)
Unfasten the bolts.
(2)
Insert the blade of SST (09215-3C000) between the lower crankcase and the oil pan. Separate the applied sealer and remove the oil pan.

   
•
Loosen one oil pan bolt near each corner of the oil pan leaving the bolts held in by about 2 threads. Then remove all other pan bolts.
   
•
Insert the SST between the oil pan and the lower crankcase by tapping it with a plastic hammer in the direction of arrow.
•
After tapping the SST with a plastic hammer along the direction of arrow around more than 2/3 edge of the oil pan, remove it from the lower crankcase.
•
Do not turn over the SST abruptly without tapping. It is result in damage of the SST.
•
Be careful not to damage the contact surfaces of the lower crankcase and the oil pan.
4.
Remove the oil screen (A) with the gasket (B).

Installation
1.
Install the oil screen (A) with a new gasket (B).

Tightening torque
Bolt :
19.6 ~ 26.5 N.m (2.0 ~ 2.7 kgf.m, 14.5 ~ 19.5 lb-ft)
Nuts :
11.8 ~ 13.7 N.m (1.2 ~ 1.4 kgf.m, 8.7 ~ 10.1 lb-ft)

2.
Install the oil pan.
(1)
Using a gasket scraper, remove all the old packing material from the gasket surfaces.
(2)
The sealant locations on the oil pan and the lower crankcase must be free of harmful foreign materials, oil, dust and moisture.
Spraying cleaner on the surface and wiping with a clean duster.
(3)
After applying liquid sealant on the oil pan, assemble it within 5 minutes after sealant was applied. Continuous bead of sealant should be applied to prevent any path of oil leakage.

Bead width
Whole section :4.0 ~ 5.0 mm (0.16 ~ 0.20 in.)
Section A : 1.5 ~ 2.5 mm (0.06 ~ 0.10 in.)
Sealant: Threebond 1217H (Hyundai Gray RTV)

   
•
When applying sealant gasket, sealant must not be protruded into the inside of oil pan.
•
If the sealant is applied to the bottom surface of the lower crankcase, it should be the same position as the oil pan.
(4)
Install the oil pan (A). Uniformly tighten the bolts in several passes.

Tightening torque:
11.8 ~ 13.7 N.m (1.2 ~ 1.4 kgf.m, 8.7 ~ 10.1 lb-ft)

   
•
After assembly, wait at least 30 minutes before filling the engine with oil.
   
•
Always use a new drain plug gasket.
3.
Refill engine with engine oil.
Oil Pan Components and Components Location
Components 1. Oil screen gasket2. Oil screen3. Oil pan ...

Oil Pump Components and Components Location
Components 1. Timing chain cover2. Outer roter3. Inner roter4. Oil pump cover5. Relief plunger6. Relief spring7. Relief plug8. O-ring (suction side)9. O-ring (discharge side) ...

Other information:

Hyundai Elantra AD (2016-2020) Owners Manual: Door Locks
Operating Door Locks from Outside the Vehicle Mechanical key If you lock the driver's door with a mechanical key, all vehicle doors will lock. If you unlock the driver's door with a mechanical key, the driver's door will unlock and the passenger doors will unlock according to the ...

Hyundai Elantra AD (2016-2020) Service Manual: General Safety Information and Caution
Precautions General Precautions Please read the following precautions carefully before performing the airbag system service. Observe the instructions described in this manual, or the airbags could accidentally deploy and cause damage or injuries. • Except when performing electrical inspe ...

© 2018-2026 www.helantraad.com