Hyundai Elantra: General Information / Specifications
| Specification |
| Engine | Transaxle | Joint type | Max. permissible angle | ||
| Outer | Inner | Outer | Inner | ||
| GAMMA 1.6 GDI | 6 MT | BJ#23 | CTJ#23 | 46.5° | 23° |
| 6 A/T | BJ#23 | CTJ#22 | |||
| UII 1.6MT / DCT | 6 MT | BJ#24 | CTJ#24 | 46.5° | 23° |
| 7DCT | BJ#24 | CTJ#24 | |||
| NU 2.0 | 6 MT | BJ#23 | CTJ#23 | 46.5° | 23° |
| 6 A/T | BJ#23 | CTJ#23 | |||
| GAMMA 1.6 T-GDI | 6 MT | BJ#23 | CTJ#23 | 46.5° | 23° |
| 7DCT | BJ#24 | CTJ#24 | |||
| Tightening torque |
| Item | N.m | kgf.m | lb-ft | |
| Front | Hub nuts | 107.9 ~ 127.5 | 11.0 ~ 13.0 | 79.6 ~ 94.0 |
| Driveshaft caulking nut | 274.6 ~ 294.2 | 28.0 ~ 30.0 | 202.5 ~ 217.0 | |
| Strut assembly to knuckle | 156.9 ~ 176.5 | 16.0 ~ 18.0 | 115.7 ~ 130.2 | |
| Front caliper to knuckle | 78.5 ~ 98.1 | 8.0 ~ 10.0 | 57.9 ~ 72.3 | |
| Wheel speed sensor mounting bolt | 7.8 ~ 11.8 | 0.8 ~ 1.2 | 5.8 ~ 8.7 | |
| Disc fixing screw | 4.9 ~ 5.9 | 0.5 ~ 0.6 | 3.6 ~ 4.3 | |
| Lower arm to knuckle | 58.8 ~ 70.6 | 6.0 ~ 7.2 | 43.4 ~ 52.1 | |
| Tie rod end castle nut | 24.5 ~ 34.3 | 2.5 ~ 3.5 | 18.1 ~ 25.3 | |
| Rear | Hub nuts | 107.9 ~ 127.5 | 11.0 ~ 13.0 | 79.6 ~ 94.0 |
| Rear caliper to torsion beam axle | 63.7 ~ 73.5 | 6.5 ~ 7.5 | 47.0 ~ 54.2 | |
| Wheel speed sensor mounting bolt | 8.8 ~ 13.7 | 0.9 ~ 1.4 | 6.5 ~ 10.1 | |
| Disc fixing screw | 4.9 ~ 5.9 | 0.5 ~ 0.6 | 3.6 ~ 4.3 | |
| Rear herb assembly to torsion beam axle | 49.0 ~ 58.8 | 5.0 ~ 6.0 | 36.2 ~ 43.4 | |
|
| Lubricants |
| Engine | Joint type | Lubricants | Quantity |
| GAMMA 1.6 A/T | BJ | RBA | 90g + 10g |
| TJ | CW09-VX21 | 120g + 10g | |
| GAMMA 1.6 M/T, NU2.0 GAMMA T-GDI M/T | BJ | RBA | 90g + 10g |
| TJ | CW09-VX21 | 125g + 10g | |
| U2 1.6MT / DCT | BJ | RBA | 100g + 10g |
| GAMMA T-GDI DCT | TJ | CW09-VX21 | 130g + 10g |
Special Service Tools
Special Service Tools
Tool(Number and Name)IllustrationUse09495-3K000Band installerInstallation of ear type boot band09495-39100Band installerInstallation of hook type boot band09568-1S100Ball jo ...
Other information:
Hyundai Elantra AD (2016-2020) Service Manual: Engine Control Module (ECM) Repair procedures
Removal
•
When replacing the ECM, the vehicle equipped withthe immobilizer must be performed procedure asbelow.
[In the case of installing used ECM]
1) Perform "ECM Neutral mode" procedure with GDS.
(Refer to Body Electrical System - "Immobilizer System")
2) After ...
Hyundai Elantra AD (2016-2020) Service Manual: Auto Defoging Actuator Repair procedures
Inspection
1.
Turn the ignition switch OFF.
2.
Disconnect the auto defogging connector.
3.
Verify that the auto defogging actuator operates to the open
position when connecting 12V to terminal 3 and grounding terminal 4.
Verify that the auto defogging actuator operates to the close ...
