Hyundai Elantra: Fuel Delivery System / Repair procedures

Hyundai Elantra AD (2016-2020) Service Manual / Engine Control/Fuel System / Fuel Delivery System / Repair procedures

Fuel Pressure Test

Release the residual pressure in fuel line.

(Refer to Fuel Delivery System - “Release Residual Pressure in Fuel Line”)

•	When removing the fuel pump fuse, a Diagnostic Trouble Code (DTC) may occur. Delete the code with the GDS after completion of “Release Residual Pressure in Fuel Line” work.

Install the Special Service Tool (SST).

(1)

Disconnect the fuel feed tube from the delivery pipe.

•	There may be some residual pressure even after “Release Residual Pressure in Fuel Line” work, so cover the hose connection with a shop towel to prevent residual fuel from spilling out before disconnecting any fuel connection.

(2)	Install the special service tool for measuring the fuel pressure in between the fuel feed tube and the fuel delivery pipe (Refer to the figure below).

3.	Inspect fuel leakage on connections among the fuel feed tube, the delivery pipe, and the SST components with IG ON.

Measure Fuel Pressure.

(1)

Start the engine and measure the fuel pressure at idle.

Fuel Pressure :

355 ~ 365 kPa (3.4 ~ 3.7 kgf/cm?, 48.6 ~ 52.9 psi)

•	If the fuel pressure differs from the standard value, repair or replace the related part (Refer to the table below).

Fuel Pressure	Cause	Related Part
Too Low	Fuel filter clogged	Fuel Filter
Too Low	Fuel leakage	Fuel Pressure Regulator
Too High	Fuel pressure regulator valve stuck	Fuel Pressure Regulator

(2)

Stop the engine, and then check for the change in the fuel pressure gauge reading.

Standard Value: The gauge reading should hold for about 5 minutes after the engine stops

•	If the gauge reading should not be held, repair or replace the related part (Refer to the table below).

Fuel Pressure (After Engine Stops)	Cause	Related Part
Fuel Pressure Drops Slowly	Leakage on injector	Injector
Fuel Pressure Drops Immediately	Check valve of fuel pump stuck open	Fuel Pump

(3)	Turn the ignition switch OFF.

Release the residual pressure in fuel line.

(Refer to Fuel Delivery System - “Release Residual Pressure in Fuel Line”)

•	When removing the fuel pump fuse, a Diagnostic Trouble Code (DTC) may occur. Delete the code with the GDS after completion of "Release Residual Pressure in Fuel Line" work.

Test End

(1)	Remove the Special Service Tool (SST) from the fuel feed tube and the delivery pipe.

(2)	Connect the fuel feed tube and the delivery pipe.

Release Residual Pressure in Fuel Line

•	There may be some residual pressure even after "Release Residual Pressure in Fuel Line" work, so cover the hose connection with a shop towel to prevent residual fuel from spilling out before disconnecting any fuel connection.

1.	Turn the ignition switch OFF and disconnect the battery (-) cable.

2.	Remove the fuel pump fuse (A).

3.	Connect the battery (-) cable.

4.	Start the engine and let idle, and then turn the ignition switch OFF after the engine has stopped on its own.

Components and Components Location

Components Location 1. Fuel tank2. Fuel pump3. Fuel filter4. Fuel pressure regulator5. Canister6. Fuel tank air filter 7. Fuel tank pressure sensor (FTPS) 8. Canister close valve (CCV)9. Fu ...

Fuel Tank Repair procedures

Removal 1. Release the residual pressure in fuel line. (Refer to Fuel Delivery System - "Release Residual Pressure in Fuel Line") 2. Remove the rear seat cushion. (Refer to Body - "Rear Se ...

Other information:

Hyundai Elantra AD (2016-2020) Service Manual: Input Speed Sensor Description and Operation
Description Input speed sensor is a vital unit that measures the rate of rotation of the input shaft inside the transaxle and delivers the readings to the TCM. The sensor provides critical input data that's used in feedback control, damper clutch control, gear setting control, line pressu ...

Hyundai Elantra AD (2016-2020) Owners Manual: Limitations of the System
The LKA system may operate prematurely even if the vehicle does not depart from the intended lane, OR, the LKA system may not warn you if the vehicle leaves the intended lane under the following circumstances: When the lane and road conditions are poor It is difficult to distinguish the lan ...